MATERIALS Wanted
Two '/*" x Γ eighteen-gauge sterling silver sheet silver Two seven/«" sterling silver bar elements Two 5.three mm x three.two mm 16-gauge sterling silver oval jump rings Two sterling silver ear wires
Resources Required
Ruler
Marker
Jeweler's observed or tin snips Masking tape
Concrete block or landscape paver
Hammer
File
High-quality grit sanding pad Awl
Really hard, flat floor /Îί’ drill bit
Handheld rotary tool, flex shaft, or drill push Liver of sulfur or oxidizing Resolution Fantastic steel wool Sprucing cloth
Two pairs of chain nose pliers
one.Make use of the ruler to measure and mark two
rectangle parts of 18-gauge sterling sheet silver.
two.Utilizing a jeweler's saw or tin snips, Slice the 18-gauge sterling sheet silver into two Vi" x Γ rectangles (if you will be building the bracelet and pendant tasks, you might want to Lower all of the rectangle silver items needed for the opposite projects and texture them all at just one time).
3.Area The 2 W x Γ sterling silver rectangle pieces on to the sticky facet of a piece of masking tape. This will let you to hold the silver rectangles in position if you are texturing them, and may also aid to keep the fingertips at a secure distance to stay away from hitting them While using the hammer.
4.Spot the bit of masking tape While using the silver rectangles sticky side down onto a concrete block or landscape paver.
5.Using a hammer, Carefully strike the tape-protected silver rectangles employing a business strike, but don't hit also challenging. You may reach the specified texture additional conveniently with various tender strikes rather then a few hard strikes. Carry the tape routinely and Test the progress of the texturing, ensuring that that all the floor in the silver rectangles is getting a uniform texture. The floor will seem similar to sandpaper if you are employing a concrete block. If you attain the specified texture, take away the silver rectangles in the masking tape.
six.the silver rectangles can have a slight curve to them, and the sides is going to be misshapen and sharp after you texture them. You may leave the silver rectangles curved or, to flatten them, area the silver rectangles on a tough, flat surface area and make use of a rawhide mallet to flatten them. If you don't Have a men's gold & silver rings very rawhide mallet, you could spot the silver rectangles on a tough, flat area, go over the parts with a thick piece of scrap leather, and make use of a hammer to Carefully faucet the leather coated silver rectangles to flatten them.
seven.You must utilize a file to eliminate any rough or sharp edges. Use a wonderful grit sanding pad to go about the region men's gold & silver rings in which you have submitted to sleek the sides and take away any file marks.
eight.Evaluate from just one conclusion of each and every textured silver rectangle and put a mark in the middle of each bit. This is when the holes might be drilled to attach the leap ring and bar elements.
9.Placed on the protection glasses. Location the textured silver rectangles onto a buy men's rings tough, flat floor. Area the point of the awl on the mark that you choose to built '/t" with the conclude from the rectangle parts and make use of a hammer to firmly strike as soon as on the best on the awl to produce a pilot hole men's college ring for drilling the holes into the silver rectangles.
10.Using a drill little bit, drill holes into Every of your silver rectangles by using a handheld rotary tool, flex shaft, or drill push. Make sure to use safety glasses.
eleven.Use the file or sanding pad to do away with any burs or rough edges still left from drilling holes into your silver rectangles.
12.Implement liver of sulfur or oxidizing solution on the textured silver rectangles, bar factors. and jump rings. It is vital to abide by any safety suggestions the maker implies when dealing with any chemicals.
13.Soon after implementing the oxidizing solution, use good steel wool to get rid of the darkened regions over the lifted area of your silver rectangles, leaving a few of the textured locations dark. Rub the good steel wool more than the jump rings and bar components to remove some although not the entire darkened spots. Rinse with h2o, dry, and rub with sharpening cloth.
14.With two men's rings personalized and engraved set of chain nose pliers pointing up, maintain the leap ring With all the opening at the very best. Roll one within your wrists clear of you and your other wrist toward you, opening the bounce ring only up to required. To shut the soar ring, hold it the same way and roll your wrists in the alternative path (think of Keeping a piece of paper and tearing it). Under no circumstances pull the leap ring finishes out as this can weaken the metallic, and it will be tricky to close the soar ring.
15.Incorporate the bar component and textured silver rectangle on the jump ring. Near the soar ring.
16.Gently open up the loop at The underside in the ear wire, increase the other conclude of the bar element. and afterwards close the ear wire loop.
17.Repeat these methods for the 2nd earring.